(ÁÖ)ÄÚ¸°½º

ºÐ·ù °Ë»ö

ÇöÀçÀ§Ä¡ : Home > > >

 
ÀÌÀü Å« À̹ÌÁö ´ÙÀ½

AM6632002 Industrial Circuit Tracing System

Á¦Á¶»ç : DAVIS
Á¦Ç°¹øÈ£:AM6632002
½ÃÁß°¡°Ý : ¿ø
ÆǸŰ¡°Ý  : ¿ø
Æ÷ÀÎÆ® : Á¡
¼ö·® :
  PLUS   MINUS   °³
¡á ȸ¿ø°¡ÀÔÀ» ÇϽøé ÇÒÀεȰ¡°ÝÀ» º¸½Ç¼ö ÀÖ½À´Ï´Ù.
¡á ¸ðµç°¡°ÝÀººÎ°¡¼¼º°µµ ÀÔ´Ï´Ù.
¡á ȸ¿øÀÌ µÇ½Ã¸é °¡°Ýº¯µ¿Á¤º¸, ½ÅÁ¦Ç°, ƯÆÇÁ¦Ç°, ±â¼úÁ¤º¸µî ´Ù¾çÇÑ
´º½ºÁ¤º¸¸¦ º¸³»µå¸³´Ï´Ù.
¡á 30¸¸¿ø¹Ì¸¸Àº Åùèºñ 3,000¿ø(ÂøºÒ)ÀÔ´Ï´Ù.
¡á Ä«µå°áÀç½Ã ¼¼±Ý°è»ê¼­ ¹ßÇà ºÒ°¡ÇÕ´Ï´Ù.
¡á ¹è¼ÛÀº Æò±Õ 2~3ÀÏÁ¤µµ ¿¹»óµË´Ï´Ù.

»ó¼¼ÆäÀÌÁö¸¦ ¸¶ÀÌÇÇÇ÷Πº¸³»±â - À¥¿ë »ó¼¼ÆäÀÌÁö¸¦ twitter·Î º¸³»±â »ó¼¼ÆäÀÌÁö¸¦ facebookÀ¸·Î º¸³»±â »ó¼¼ÆäÀÌÁö¸¦ Me2Day·Î º¸³»±â

The receiver has two detectors in its tip which are tuned to pick up the electromagnetic signals
Designed to handle the majority of tracing applications, the AT-2000 series of Advanced Tracers combine 11 years of experience and three different technologies into one multipurpose instrument. Economically priced, fully portable and easy to use, the AT-2000 series has the following capabilities.

The receiver has two detectors in its tip which are tuned to pick up the electromagnetic signals (¡°short¡± mode) or electrostatic signals (¡°open¡± mode) generated by the other components. The LED's and sensitivity settings indicate the relative signal strength to allow easy detection of the signal source. The receiver is included.

The load signal generator , when connected to an energized line, will draw a rapidly fluctuating current pulse from the source, causing the power line to emit an electromagnetic signal which is detected by the receiver in the 'short' mode.

These devices allow tracing of line-side conductors without power interruption or interference. The generator accepts 9-600V AC or DC and comes with the AT-2002 and AT-2004.

The transmitter injects a signal into an unenergized conductor. If the conductor is broken (open), no current will flow, so the signal is present as a voltage pulse, which is detected along the conductor's length by the R2000's electrostatic detector ('open' mode). The signal will stop at the open. The transmitter comes with the AT-2004.

When the Inductive Clamp is clamped around an energized line and plugged into the transmitter, it will induce a signal onto the down-stream (load) side to enable identification of equipment on that circuit. The clamp only comes with the AT-2004.
 
AT-2002
  • Industrial Circuit Tracing System
  • Includes the Receiver
  • Load Signal Generator (9-600V AC/DC)
  • Cordsets
  • Adapter and Manual
 
AT-2004
  • Industrial Multipurpose Tracing System
  • Includes the Receiver
  • Load Signal Generator
  • Transmitter
  • Clamp and Cordsets
  • Adapter and Owners Manual
 
Applications
  • Trace conductors buried up to 13 feet
  • Trace and identify load-side equipment from the circuit breaker while energized
  • Trace line-side wiring power interruption on circuits from 9 to 600 Volts AC or DC
  • Trace open wires for over a mile
  • Trace wire in conduit or, even the conduit itself
  • Locate ground faults and shorts
  • Identify individual wires in a bundle
  • All units are fully fused, protected and intrinsically safe
 
CAT NO. MODEL DEscRIPTION AVAIL PRICE
AM6632002   AT-2002   INDUSTRIAL WIRE CIRCUIT TRACING SYSTEM   Yes   1,509,840
AM6632004   AT-2004   INDUSTRIAL MULTI-PURPOSE TRACING SYSTEM   Yes   2,106,000
AM6632005   B2024   OPTIONAL 24V NiCAD BATTERY BOOSTER FOR Wire Circuit Tracing System   Yes   300,132

 

AM6632006   B2025   OPTIONAL 115V/24VDC BATTERY BOOSTER CHARGER FOR Wire Circuit Tracing System   Yes   88,452

 

¡¡